Assessment of Automobile Engines Rebuilt at Local Artisan Workshops in Ghana

Authors

  • Prince Yaw Andoh Kwame Nkrumah University of Science and Technology
  • Godwin Kafui Ayetor Kwame Nkrumah University of Science and Technology
  • Kofi Owura Amoabeng Kwame Nkrumah University of Science and Technology
  • Michael Nii Sackey Sackey Kwame Nkrumah University of Science and Technology

DOI:

https://doi.org/10.37385/jaets.v3i2.314

Keywords:

Engine Rebuilt, Local Artisans, Cylinder Re-bore, Piston Ring, Automobile

Abstract

The manufacturing industry of Ghana, as promising as it is, has many shaping to be done. This specifically goes to the automobile manufacturers and engine rebuilders of Ghana. Though agile and very skillful in rebuilding engines many have reported grievances on their service renders to them. This shows that, the knowledge and zeal to rebuild it puts the industry at a certain level but needs further additional and requisite tuning to reach the pinnacle. For this reason, the researcher therefore sought to investigate how cylinder bores and piston ring end-gap contribute to the failure of locally rebuilt engines. A descriptive design was used for the study and sample of 60 participants responded to the structured questionnaire. The study used primary data to provide reliable and up-to-date information the researcher needs for the analysis. The data were entered in SPSS with analysis performed using inferential and descriptive analysis methods. The findings of the study revealed that errors made in the work procedure had a stronger effect on the clients’ than its other counterpart. Practically, the flaws in the work procedure of rebuilding cylinder bore significantly affects clients’ satisfaction.

Downloads

Download data is not yet available.

References

Blossfeld, D. H., Schneider, E. W., Lechman, D. C., Hill, R. F., Reising, R. F., Brevick., J. E. (1993). Effect of Cylinder Bore Out-of-Roundness on Piston Ring Rotation and Engine Oil Consumption. SAE Technical Paper 930796, p. 1

Carley Larry. (2012). Cylinder Bores- Machining to Sleeving. Engine Builder. Available at: https://www.enginebuildermag.com/2012/01/cylinder-bores-machining-to-sleeving/

Carley Larry. (2000). Cylinder Bores- Machining to Sleeving. Engine Builder. Available at:

https://www.enginebuildermag.com/2000/09/cylinder-bore-surface-finishes/

Lei Chen. (2017). Cylindrical Machining Workpiece Temperature and Bore Cylindricity. Doctoral dissertation, The University of Michigan. https://deepblue.lib.umich.edu/handle/2027.42/137076

Dimkovski, Z., Cabanettes, F., Lofgren, H. & Anderberg, C. (2012). Optimisation of Cylinder Liner Surface Finish by Slide Honing. Journal of Engineering Manufacture, 4(226), pp. 575-584.

Fitch Jim C. (2012). Analysis of In-Service Automotive Engine Oils. In Automotive Lubricants and Testing. ASTM International, 2012. Pp 399-345. https://doi.org/10.1520/MNL6220121210122

Flynn B., Pagell M. and Fugate, B. (2017). Survey research design in supply chain management: the need for evolution in our expectations. Journal of Supply Chain Management, 54(1). DOI: 10.1111/jscm.12161.

Hair Jr, J. F., Babin, B. J. and Krey, N. (2017) ‘Covariance-based structural equation modeling in the Journal of Advertising: Review and recommendations’, Journal of Advertising, 46(1), pp. 163–177.

Huizenga, P. (2018). Everything You Need to Know About Ring Gap! WiSECO. Available at: http://blog.wiseco.com/everything-you-need-to-know-about-ring-gap

Khan, M. Q., Masood, S. A. and Qureshi, S. N. (2019) ‘Analysis of low productivity in public sector automobile’, Technical Journal, 24(01), pp. 51–62.

Labore, E., (2017). How to Check Piston to Cylinder Bore Clearance with Mahle Motorsport. DRAGZINE. Available at: https://www.dragzine.com/news/how-to-check-piston-to-cylinder-bore-clearance-with-mahle-motorsport/

Mai, Y., Zhang, Z. and Wen, Z. (2018) ‘Comparing exploratory structural equation modeling and existing approaches for multiple regression with latent variables’, Structural Equation Modeling: A Multidisciplinary Journal, 25(5), pp. 737–749.

Mansori, M. E., Goeldel, B. & Sabri, L., (2013). Performance impact of honing dynamics on surface finish of precoated cylinder bores. Surface and Coatings Technology, Issue 215, pp. 334-339.

Mensah, J. T. and Adu, G., (2015) ‘An empirical analysis of household energy choice in Ghana’, Renewable and Sustainable Energy Reviews, 51, pp. 1402–1411. doi: 10.1016/j.rser.2015.07.050.

Pravin, P. S., Misra S., Bhartiya, S., and Gudi, R. D., (2020) ‘A reactive scheduling and control framework for integration of renewable energy sources with a reformer-based fuel cell system and an energy storage device’, Journal of Process Control, 87, pp. 147–165. doi: 10.1016/j.jprocont.2020.01.005.

Shafie, S. M., (2016) ‘A review on paddy residue-based power generation: Energy, environment and economic perspective’, Renewable and Sustainable Energy Reviews, 59, pp. 1089–1100. doi: 10.1016/j.rser.2016.01.038.

Sherrington, I., Ma, M. & Smith, E. H., (1995). Effects of Bore Out-of-Roundness on the Predicted Performance of Piston Rings in Internal Combustion Engines. Elsevier Science B. V., pp. 367-379.

Smith, J. (2019). Piston Ring Gap: How Important Is It, And How to Get It Right. CHEVYHARDCORE. Available at: https://www.chevyhardcore.com/tech-stories/engine/piston-ring-gap-how-to-get-them-correct/

Tim Charlet. (2015). What Are the Benefits of Having an Engine Rebuilt Instead of Replaced? Your Mechanic. Available at: https://www.yourmechanic.com/article/what-are-the-benefits-of-having-an-engine-rebuilt-instead-of-replaced

Tobi, H. and Kampen, J. K., (2018) ‘Research design: the methodology for interdisciplinary research framework’, Quality & quantity, 52(3), pp. 1209–1225.

Thomas, T. K., (2019) ‘Automobile Piston Ring Design’, International Journal of Science and Research, 8 (6), pp 865-867.

Wahab, D. A., Blanco-Davis, E., Ariffin, A. K., Wang, J. (2018) ‘A review on the applicability of remanufacturing in extending the life cycle of marine or offshore components and structures’, Ocean Engineering, 169, pp. 125–133.

Wos, P. & Michalski, J., (2011). Effect of Initial Cylinder Liner Honing Surface Roughness on Aircraft Piston Engine Performances. Tribology Letters, 3(41), pp. 555-567.

Wulfmeyer, V., Turner, D. D., Baker, B., Banta, R. (2018) ‘A new research approach for observing and characterizing land–atmophere feedback’, Bulletin of the American Meteorological Society, 99(8), pp. 1639–1667.

Zhan, L., Liang, F., Zhai, L., Meng, X., (2021) ‘A comprehensive experimental study on tribological performance of piston ring–cylinder liner pair’ Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, doi.org/10.1177/13506501211004758.

Downloads

Published

2022-06-10

How to Cite

Andoh, P. Y., Ayetor, G. K., Amoabeng, K. O., & Sackey, M. N. S. (2022). Assessment of Automobile Engines Rebuilt at Local Artisan Workshops in Ghana. Journal of Applied Engineering and Technological Science (JAETS), 3(2), 53–66. https://doi.org/10.37385/jaets.v3i2.314